DGK Pellachrom | decorative and marine paints | - Header Section

DGK Pellachrom | decorative and marine paints | - Main Section

DGK Pellachrom | decorative and marine paints | - Main Component

water
SOLVENT BASED
  • 750 ml
  • 2.5 L

POLYGLOSS

polyurethane top coat

Premium two-part polyurethane top coat, extremely resistant to adverse weather conditions. Long-lasting bright colours with excellent yellowing resistance. Excelling durable gloss. Gives an extremely tough and elastic surface with great resistance to tear and knocks while it creates a flawless finish. Its composition ensures excellent results on all surfaces. Ideal for indoor and outdoor use on highly demanding surfaces. Ideal for any type of boat.

  • premium high-gloss finish
  • long-lasting shades
  • extreme chemical and mechanical resistance
xrisi4xrisi4
BUILDINGS
INTERIOR-EXTERIOR USE
xrisi4xrisi4
FREEBOARDS - UNDERWATER HULL
highgloss
Finish
toolsall
TOOLS
POLYGLOSS
THINNING
1 hr
DRYING TIME
2-4 hrs
OVERCOATING INTERVAL
2
RECOMMENDED COATS
14 2
m2/L
SPREADING RATES
water READY TO USE COLOR SHADES

Preparation

Carefully prepare surface to obtain good results. Remove all weathered coatings, rust and oils. Sand and remove sanding residue with a rag.

New polyester:
Degreasing new polyester is of utmost importance. Please follow the proposed procedure: Wash surface with warm water and soap (detergent). Rinse well, allow to dry and clean using a thinner. Sand and remove sanding residue with a whisk and a thinner soaked rag. The surface is now ready to be painted. Any other surface preparation method could trap grease inside the surface thus, rendering painting impossible. Prime with UNI-PRIMER, 1-2 coats. Apply 2 coats of POLYGLOSS.
New plaster, concrete, brick, cement and stone:
Apply POLACRYL 301 until surface saturation is achieved. Prime with UNI-PRIMER, 1-2 coats. Apply 2-3 coats of POLYGLOSS.
New wood:
Apply POLACRYL 301 until surface saturation is achieved. Prime with UNI-PRIMER, 1-2 coats. Apply 2-3 coats of POLYGLOSS.
New metal:
Prime with X-RUST, 2 coats. Apply 2-3 coats of POLYGLOSS.
New glass, tiles, enamel plates:
Prime with SMALTO GRIP, 1-2 coats. Apply 2-3 coats of POLYGLOSS.
Recoated old surfaces:
Prime with UNI-PRIMER, 1-2 coats. Apply 2-3 coats of POLYGLOSS.

Use

► Stir well component A before use to achieve homogeneity. Then, add component B progressively while constantly stirring.
► Make sure your tool has the adequate quantity of paint to cover an entire section. This practice should be strictly followed to obtain optimum results.
► Sand surface smooth with the right sandpaper for the task before painting.
► To prevent bubble forming during application, work in an area protected against direct sunlight if possible.
► Do not apply when ambient temperature and surface temperature is below 10°C, above 35°C and when relative humidity is above 70%.
► To improve the chemical resistance and the mechanical properties of the final surface, add ADDITIVE 640 before application of the last coat.
► Make sure that the colour of the support is perfectly covered before application of POLYGLOSS mixed with ADDITIVE 640.
► Adequate ventilation must be ensured due to the hazardous fumes generated during paint application.

Drying out - coverage

Drying times are dependent on ambient temperature and film thickness.

Touch dry: 1 hour.

Recoat: 2-4 hours.

Practical coverage: 12-16m²/lt depending on the thickness of each coat and the surface porosity. 

DGK Pellachrom | decorative and marine paints | - Bottom info

Calculate the quantity of the paint

you need for