DGK Pellachrom | decorative and marine paints | - Header Section

DGK Pellachrom | decorative and marine paints | - Main Section

DGK Pellachrom | decorative and marine paints | - Main Component

water
SOLVENT BASED
  • 750 ml
  • 3 L
  • 7.5 L
  • 15 L

POOLGLOSS

swimming pool polyurethane paint

Premium two-pack swimming pool polyurethane paint with high hiding capacity and quick-drying properties for use on bare or previously painted concrete pools. Resistant to adverse weather conditions. Adheres tightly to the concrete, resists chalking and peeling. Provides a high gloss, elastic and tough finish with great abrasion resistance. Particularly resistant to chlorine, sun tanning oils, pool chemicals and sea water. Ideal for hotel and residential pools.

  • extreme chemical and mechanical resistance
  • long-lasting resistance to UV radiation
  • excellent adhesion
xrisi2xrisi2
BUILDINGS
INTERIOR-EXTERIOR USE
gloss
Finish
toolsall
TOOLS
POOLGLOSS
THINNING
1-2 hr
DRYING TIME
6-12 hrs
OVERCOATING INTERVAL
2- 3
RECOMMENDED COATS
9 2
m2/L
SPREADING RATES
water READY TO USE COLOR SHADES
900
991
992
992

Preparation

Carefully prepare surface to obtain good results. Surface must be clean, dry and free from loose or flaking material, dust, oils and salts.

New cement or mortar:
Allow one month after pool construction before painting. The pool must be dry and free from humidity and any dust particle. Apply a 10% hydrochloric acid solution for the pores to open and for obtaining a tighter grip between the surface and the coat. Once you apply the HCI, rub with a brush until the bubbling action of the acid stops. Rinse HCI well with plenty of water. Rub the surface to remove any foreign material. Leave at least one week to dry before painting the pool. If pool insulation is required, apply POLACRYL 301 until surface saturation is achieved. Apply 2-3 coats of POOLGLOSS.
New glass, tiles, enamel plates:
Prime with SMALTO GRIP, 1-2 coats. Apply 2-3 coats of POOLGLOSS.
New stone:
Apply POLACRYL 302 until surface saturation is achieved and sand surface smooth. Apply 2-3 coats of POOLGLOSS.
Recoated old surfaces:
Remove any dirt and loose material with a wire brush. Rinse with water. Make sure that the surface is dry before paint application. Prime with UNI-PRIMER, 1-2 coats, where necessary. Apply 2-3 coats of POOLGLOSS.

Use

► Stir well component A before use to achieve homogeneity. Then, add component B progressively while constantly stirring.
► Make sure your tool has the adequate quantity of paint to cover an entire section. This practice should be strictly followed to obtain optimum results.
► Sand surface smooth with the right sandpaper for the task before painting.
► To prevent bubble forming during application, work in an area protected against direct sunlight if possible.
► Do not apply when ambient temperature and surface temperature is below 10°C, above 30°C or when relative humidity is above 50% and surface humidity is above 4%.
► Apply the first coat with a roller, a brush or an airless gun sprayer thinned with THINNER 120 by 5-20%. Apply the second coat thinned with THINNER 120 by 5-10%.
► Never paint a wet pool. Start painting three hours after sunrise and make sure that you have finished your painting project three hours before sunset. This will prevent dampness and moisture condensation on the newly painted surface.

Drying out - coverage

Drying times are dependent on ambient temperature and film thickness.

Touch dry: 1-2 hours.

Recoat: 6-12 hours.

Practical coverage: 7-11m²/L depending on the thickness of each coat and the surface porosity.

DGK Pellachrom | decorative and marine paints | - Bottom info

Calculate the quantity of the paint

you need for